problemy z ekranem

Gdy jakieś urządzenie nie chce w Slackware działać...

Moderatorzy: Moderatorzy, Administratorzy

jogofrugo
Użytkownik
Posty: 9
Rejestracja: 2007-04-20, 15:10

problemy z ekranem

Post autor: jogofrugo »

Witam wszystkich forumowiczów to jest mój pierwszy post tak?e prosi? bym o wyrozumia?o??

konfiguracja sprzetowa i programowa:

karta graficzna:
geforce4 mx 440se

monitor:
viewpoint 15"
model: VP 1570 OA
typ: J51A
(niewiem nic poza faktem ?e w windowzie mia?em rozdzielczo?? 1024 768 85 hz 32bitcolor) natomiast na pewnej stronie http://www.ciao.co.uk/Viewpoint_15_VP1570_OA__5395353 znalaz?em co? takieego
Diagonal Size: 15"
Viewable Size: 13.7"
Dot Pitch / Pixel Pitch: 0.28 mm
Max Resolution: 1280 x 1024 / 60 Hz
Max Sync Rate (V x H): 90 Hz x 70 kHz
Factory Preset Resolution Modes:
1280 x 1024 / 60 Hz
1024 x 768 / 85 Hz
Front Panel Controls: Power on/off, adjust +/- , enter
On-Screen Controls: H/V-position, H/V-size, pincushion distortion, trapezoid, parallelogram, language select, tilt, OSD-position
Interface: VGA (HD-15)

teraz troch? o systemie linux jaki posiadam:
System: Slackware 10.2
Jadro: 2.4.31
sterownik nvidi: NVIDIA-Linux-x86-1.0-9631-pkg.run

Plik xorgconf:

Kod: Zaznacz cały

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder3)  Thu Nov  9 17:55:20 PST 2006


Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    FontPath "/usr/X11R6/lib/X11/fonts/100dpi_pl"
    FontPath "/usr/X11R6/lib/X11/fonts/75dpi_pl"
    FontPath "/usr/X11R6/lib/X11/fonts/misc_pl"

    RgbPath         "/usr/X11R6/lib/X11/rgb"
    ModulePath      "/usr/X11R6/lib/modules"
    FontPath        "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath        "/usr/X11R6/lib/X11/fonts/TTF/"
    FontPath        "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath        "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath        "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath        "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection

Section "Module"
    Load           "glx"
    Load           "record"
    Load           "extmod"
    Load           "dbe"
    Load           "xtrap"
    Load           "freetype"
    Load           "type1"
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "kbd"
	Option "XkbModel" "pc104"
	Option "XkbLayout" "pl"
EndSection

Section "InputDevice"
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/mouse"
EndSection

Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Monitor Vendor"
    ModelName      "Monitor Model"
    VertRefresh     75
EndSection

Section "Device"
    Identifier     "Card0"
    Driver         "nvidia"
    VendorName     "nVidia Corporation"
    BoardName      "NV17 [GeForce4 MX 440-SE]"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    DefaultDepth 24
    SubSection "Display"
        Viewport   0 0
        Depth     1
        Modes    "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
        Modes    "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
        Modes    "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
        Modes    "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
        Modes     "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
        Modes     "1024x768" "800x600" "640x480"
    EndSubSection
EndSection
mój problem:
przy standardowych sterownikach (odrazu po instalacji) mialem do wyboru jedno od?wierzanie 60hz i rozdzielczo?ci 640x480, 320x240,320 200.
po zainstalowaniu sterownikówwy?ej wymienionych do wyboru juz nic nie mialem rodzielczo?? jaka byla ustawiona to 800x600 i odswiezanie jakie mi wykrywa to 50hz w ustawieniach system/ nvidia x serw.... settings nie mozna wybrac ?adnej rodzielczo?ci gdy? jest ona ustawiona na auto i odswierzanie jest zablokowane i nie do wyboru

co robi? panowie ? zebym mogl ustawi? rodzielczo?? na 1024x768_85hz
oczy mnie juz strasznie bola a hce sie przestawic na linuxsa pros? was o pomoc
co do instrukcji obs?ugi monitora to nie mam wiem tylko to co napisane by?o na tej stronie powy?ej

ps. widzi?em ju? wiele w?tków na ten temat
probowalem juz:

Kod: Zaznacz cały

gtf 1024 768 85
# 1024x768 @ 85.00 Hz (GTF) hsync: 68.60 kHz; pclk: 94.39 MHz
  Modeline "1024x768_85.00"  94.39  1024 1088 1200 1376  768 769 772 807  -HSync +Vsync
gtf 1024 768 80
# 1024x768 @ 80.00 Hz (GTF) hsync: 64.32 kHz; pclk: 88.50 MHz
  Modeline "1024x768_80.00"  88.50  1024 1088 1200 1376  768 769 772 804  -HSync +Vsyn
ten modeline dorzuca??m juz do sekcji "monitor"
a w sekcji screen ustawialem

Kod: Zaznacz cały

modes "1024x768_85" "1024x768_80" "800x600"
to te? nie pomaga
prubowa?em tez wstawi?
Max Resolution: 1280 x 1024 / 60 Hz
Max Sync Rate (V x H): 90 Hz x 70 kHz
HorizSync 30.0 - 70.0 (tak mysle ze to sie bierze od 70 kHz)
VertRefresh 50 - 90 (tak mysle ?e to sie bierze od 90 Hz)

ps.2:prosz? o pomoc naprawd? poczyta?em o tym i dodam ?e instalowa?em jeszcze wcaze?niej sterowniki:
NVIDIA-Linux-x86-1.0-8178-pkg.run (te? nic)
NVIDIA-Linux-x86-1.0-5336(hyba taki numerek by?)-pkg.run


prosz? o pomoc jesli bedzie potrzeba to dosle te? loga ze startu /var/log/xorg.0.log
albo zrobie to odrazu:

Kod: Zaznacz cały

_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/Jogo:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

X Window System Version 6.8.2
Release Date: 9 February 2005
X Protocol Version 11, Revision 0, Release 6.8.2
Build Operating System: Linux 2.6.13 i686 [ELF] 
Current Operating System: Linux Jogo 2.4.31 #6 Sun Jun 5 19:04:47 PDT 2005 i686
Build Date: 11 September 2005
	Before reporting problems, check http://wiki.X.Org
	to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Apr 20 15:46:24 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/100dpi_pl,
                      /usr/X11R6/lib/X11/fonts/75dpi_pl,
                      /usr/X11R6/lib/X11/fonts/misc_pl,
                      /usr/X11R6/lib/X11/fonts/misc/,
                      /usr/X11R6/lib/X11/fonts/TTF/,
                      /usr/X11R6/lib/X11/fonts/Type1/,
                      /usr/X11R6/lib/X11/fonts/CID/,
                      /usr/X11R6/lib/X11/fonts/75dpi/,
                      /usr/X11R6/lib/X11/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(**) ModulePath set to "/usr/X11R6/lib/modules"
(WW) Open APM failed (/dev/apm_bios) (No such device)
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.2
	X.Org Video Driver: 0.7
	X.Org XInput driver : 0.4
	X.Org Server Extension : 0.2
	X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	ABI class: X.Org Video Driver, version 0.7
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1039,0735 card 0000,0000 rev 01 class 06,00,00 hdr 80
(II) PCI: 00:01:0: chip 1039,0001 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:02:0: chip 1039,0008 card 0000,0000 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:02:2: chip 1039,7001 card 1039,7001 rev 07 class 0c,03,10 hdr 00
(II) PCI: 00:02:3: chip 1039,7001 card 1039,7001 rev 07 class 0c,03,10 hdr 00
(II) PCI: 00:02:5: chip 1039,5513 card 1039,5513 rev d0 class 01,01,80 hdr 80
(II) PCI: 00:0f:0: chip 10ec,8029 card 10ec,8029 rev 00 class 02,00,00 hdr 00
(II) PCI: 00:11:0: chip 1102,0002 card 1102,8064 rev 07 class 04,01,00 hdr 80
(II) PCI: 00:11:1: chip 1102,7002 card 1102,0020 rev 07 class 09,80,00 hdr 80
(II) PCI: 00:13:0: chip 1106,3038 card 0925,1234 rev 50 class 0c,03,00 hdr 80
(II) PCI: 00:13:1: chip 1106,3038 card 0925,1234 rev 50 class 0c,03,00 hdr 80
(II) PCI: 00:13:2: chip 1106,3104 card 0925,1234 rev 51 class 0c,03,20 hdr 80
(II) PCI: 01:00:0: chip 10de,0173 card 0000,0000 rev a3 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
	[0] -1	0	0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
	[0] -1	0	0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
	[0] -1	0	0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000a (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
	[0] -1	0	0xcde00000 - 0xcfefffff (0x2100000) MX[B]
(II) Bus 1 prefetchable memory range:
	[0] -1	0	0xbdb00000 - 0xcdcfffff (0x10200000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:2:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) nVidia Corporation NV17 [GeForce4 MX 440-SE] rev 163, Mem @ 0xce000000/24, 0xc0000000/27, 0xcdc80000/19, BIOS @ 0xcfee0000/17
(II) Addressable bus resource ranges are
	[0] -1	0	0x00000000 - 0xffffffff (0x0) MX[B]
	[1] -1	0	0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
	[0] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[1] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[2] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[3] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[4] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[5] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[6] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd3ffffff to 0xcfffffff
(II) Active PCI resource ranges:
	[0] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[1] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[2] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[3] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[4] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[5] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[6] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[7] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[8] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[9] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[10] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[11] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[12] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[13] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
	[0] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[1] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[2] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[3] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[4] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[5] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[6] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[7] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[8] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[9] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[10] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[11] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[12] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[13] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
	[0] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[1] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[2] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[3] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[4] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[5] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[6] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
	[0] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[1] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[2] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[3] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[4] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[5] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[6] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[7] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[8] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[9] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[10] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[11] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[12] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[13] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[14] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[15] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[16] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[17] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[18] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[19] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[20] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
	compiled for 4.0.2, module version = 1.0.9631
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.1
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension RECORD
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "xtrap"
(II) Loading /usr/X11R6/lib/modules/extensions/libxtrap.a
(II) Module xtrap: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DEC-XTRAP
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
	compiled for 6.8.2, module version = 2.1.0
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.2
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "nvidia"
(II) Loading /usr/X11R6/lib/modules/drivers/nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
	compiled for 4.0.2, module version = 1.0.9631
	Module class: X.Org Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.4
(II) NVIDIA dlloader X Driver  1.0-9631  Thu Nov  9 17:39:58 PST 2006
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset NVIDIA GPU found
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="X.Org Foundation"
	compiled for 6.8.2, module version = 0.1.0
	ABI class: X.Org Video Driver, version 0.7
(II) resource ranges after xf86ClaimFixedResources() call:
	[0] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[1] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[2] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[3] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[4] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[5] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[6] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[7] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[8] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[9] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[10] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[11] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[12] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[13] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[14] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[15] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[16] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[17] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[18] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[19] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[20] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
(II) resource ranges after probing:
	[0] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[1] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[2] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[3] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[4] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[5] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[6] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[7] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[8] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[9] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[10] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[11] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[12] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[13] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[14] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[15] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[16] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[17] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[18] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[19] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[20] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[21] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[22] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[23] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
	[24] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[25] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): NVIDIA GPU GeForce4 MX 440-SE at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 65536 kBytes
(--) NVIDIA(0): VideoBIOS: 04.17.00.69.00
(II) NVIDIA(0): Detected AGP rate: 4X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce4 MX 440-SE at
(--) NVIDIA(0):     PCI:1:0:0:
(--) NVIDIA(0):     @@@ (CRT-0)
(--) NVIDIA(0):     NVIDIA TV Encoder (TV-0)
(--) NVIDIA(0): @@@ (CRT-0): 350.0 MHz maximum pixel clock
(--) NVIDIA(0): NVIDIA TV Encoder (TV-0): 350.0 MHz maximum pixel clock
(--) NVIDIA(0): TV encoder: NVIDIA
(II) NVIDIA(0): Assigned Display Device: CRT-0
(WW) NVIDIA(0): No valid modes for "1024x768"; removing.
(WW) NVIDIA(0): No valid modes for "800x600"; removing.
(WW) NVIDIA(0): No valid modes for "640x480"; removing.
(WW) NVIDIA(0): 
(WW) NVIDIA(0): Unable to validate any modes; falling back to the default mode
(WW) NVIDIA(0):     "nvidia-auto-select".
(WW) NVIDIA(0): 
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0):     "nvidia-auto-select"
(II) NVIDIA(0): Virtual screen size determined to be 800 x 600
(==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] 0	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B]
	[1] 0	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B]
	[2] 0	0	0xce000000 - 0xceffffff (0x1000000) MX[B]
	[3] -1	0	0xffe00000 - 0xffffffff (0x200000) MX[B](B)
	[4] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[5] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[6] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[7] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[8] -1	0	0xcfffdf00 - 0xcfffdfff (0x100) MX[B]
	[9] -1	0	0xcffff000 - 0xcfffffff (0x1000) MX[B]
	[10] -1	0	0xcfffe000 - 0xcfffefff (0x1000) MX[B]
	[11] -1	0	0xd0000000 - 0xcfffffff (0x0) MX[B]O
	[12] -1	0	0xcfee0000 - 0xcfefffff (0x20000) MX[B](B)
	[13] -1	0	0xcdc80000 - 0xcdcfffff (0x80000) MX[B](B)
	[14] -1	0	0xc0000000 - 0xc7ffffff (0x8000000) MX[B](B)
	[15] -1	0	0xce000000 - 0xceffffff (0x1000000) MX[B](B)
	[16] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
	[17] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
	[18] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
	[19] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[20] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[21] -1	0	0x0000d000 - 0x0000d01f (0x20) IX[B]
	[22] -1	0	0x0000cc00 - 0x0000cc1f (0x20) IX[B]
	[23] -1	0	0x0000dc00 - 0x0000dc07 (0x8) IX[B]
	[24] -1	0	0x0000d400 - 0x0000d41f (0x20) IX[B]
	[25] -1	0	0x0000d800 - 0x0000d81f (0x20) IX[B]
	[26] -1	0	0x0000ff00 - 0x0000ff0f (0x10) IX[B]
	[27] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
	[28] 0	0	0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) NVIDIA(0): Setting mode "nvidia-auto-select"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(II) Loading extension NV-CONTROL
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/mouse"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/mouse"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(==) Mouse0: Buttons: 3
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc104"
(**) Keyboard0: XkbModel: "pc104"
(**) Option "XkbLayout" "pl"
(**) Keyboard0: XkbLayout: "pl"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) XINPUT: Adding extended input device "NVIDIA Damage Notification Manager" (type: Other)
(II) XINPUT: Adding extended input device "NVIDIA Kernel RC Handler" (type: Other)
(II) XINPUT: Adding extended input device "NVIDIA Event Handler" (type: Other)
(**) Option "Device" "/dev/mouse"
(II) Mouse0: GuessProtocol: setting mouse protocol to "PS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
Could not init font path element /usr/X11R6/lib/X11/fonts/CID/, removing from list!
SetClientVersion: 0 8
prosz? eszcze raz o pomoc


[ Komentarz dodany przez: Lizard: 2007-04-20, 23:42 ]

Generalnie dobrze. Ale niektóre rzeczy lepiej wyglądają ujęte w znaczniki

Kod: Zaznacz cały

[/b]. ;)[/color]
Ostatnio zmieniony 2007-04-20, 22:47 przez jogofrugo, łącznie zmieniany 2 razy.

Awatar użytkownika
Radek_R
Moderator
Posty: 1196
Rejestracja: 2004-06-14, 11:40
Lokalizacja: Kraków
Kontakt:

Re: problemy z ekranem

Post autor: Radek_R »

Popraw swój post! Logi, konfigi poumieszczaj w

Kod: Zaznacz cały

I zrób coś też z kodowaniem (za dużo "?" - czyżby CP-1250?)
#358274
http://www.prook.net

kolert83
Użytkownik
Posty: 69
Rejestracja: 2006-10-16, 18:29
Lokalizacja: Śląsk

Re: problemy z ekranem

Post autor: kolert83 »

Witam

Po zalogowaniu sie na root (przed włączeniem X-ów) wpisz : xorgconfig
konfigurujesz tu ustawienia ,karty graficznej , myszki,klawiatury itp... gdzy dojdziesz do :
tego punktu :

"You must indicate the horizontal sync range of your monitor. You can either
select one of the predefined ranges below that correspond to industry-
standard monitor types, or give a specific range."

wpisz 11 , i podaj odpowiednie ustawien dla Horizontal , potem dla Vertical
potem dojdz do końca i zapisz ustawienia. ZNAJDZ tylko jakie możesz mieć max Horizontal i Vertcal

Jak by nie pomogło to pomyślimy dalej ...

Awatar użytkownika
qpalzm
Użytkownik
Posty: 172
Rejestracja: 2006-12-10, 18:07
Lokalizacja: Zabrze
Kontakt:

Re: problemy z ekranem

Post autor: qpalzm »

zrob cos z tym postem bo jak narazie to sie tego czytac nie da! (znaczniki code i zaznaczenie problemu)
Jezeli niechcesz sie bawic z xorgconfig wpisz xorgcfg - wykrywanie sprzetu przebegnie automatycznie. Pozniej zmienisz sterownik karty graficznej na nvidia i powinno smigac. Jesli nie to bedziemy poprawiac xorg.conf

wydaje mi sie ze tu lezy twoj problem

Kod: Zaznacz cały

(WW) NVIDIA(0): Unable to validate any modes; falling back to the default mode
(WW) NVIDIA(0): "nvidia-auto-select".
(WW) NVIDIA(0):
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "nvidia-auto-select"
(II) NVIDIA(0): Virtual screen size determined to be 800 x 600 
Pozdrawiam
www.xfce.daxa.pl

jogofrugo
Użytkownik
Posty: 9
Rejestracja: 2007-04-20, 15:10

Re: problemy z ekranem

Post autor: jogofrugo »

:ok:
witam poraz kolejny
przepraszam za nie zaznaczenie codu w specjalnej ramce iza kodowanie (jestem w trakcie konfiguracji ale nie chce zasmiecac tego posty konfiguracja klawiatury)
a wiec tak:
rozdzielczosc 1024x768 70hz jest i dziala juppi zadzialalo

Kod: Zaznacz cały

xorgconfig
hmmm tyle ze nie bylo tam ustawienia rozdzielczosci i odswierzania na 85 hz co z tym fantem zrobic nie znam mozliwosci mojego monitora wiem ze w winowsie dzialal na 85 hz w rozdzielczosci 1024x768.
co do pliku xorg.config to kaszanka sie chyba w nim zrobila hehehehehe postaram sie troche uporzadkowac najpierw wkleje co mam teraz a potem po uporzadkowaniu pokaze jak ladniu uporzadkowalem:
plik xorg.conf po zmianach za pomoca

Kod: Zaznacz cały

xorgconfig

Kod: Zaznacz cały

# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# 

    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/TTF/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/cyrillic/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client. 

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings. 

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier	"Keyboard1"
    Driver	"kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option	"Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"	"xorg"
    Option "XkbModel"	"pc101"
    Option "XkbLayout"	"pl"
    Option "XkbVariant"	"pl"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier	"Mouse1"
    Driver	"mouse"
    Option "Protocol"    "Auto"
    Option "Device"      "/dev/mouse"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"	"256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"	"9600"
#    Option "SampleRate"	"150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "monitor0"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5 - 57.0

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-90

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier	"Standard VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset	"generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam	256

#    Clocks	25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
    Identifier  "card0"
    Driver      "nv"
    #VideoRam    65536
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "card0"
    Monitor     "monitor0"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection

a teraz po moich zmianach i upozadkowaniu

Kod: Zaznacz cały

Section "Module"
    Load        "dbe"  	# Double buffer extension

    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection
    Load        "type1"
    Load        "freetype"
    Load       "glx"
EndSection
Section "Files"
    RgbPath	"/usr/X11R6/lib/X11/rgb"
    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/TTF/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/cyrillic/"
EndSection
Section "ServerFlags"
EndSection
    Identifier	"Keyboard1"
    Driver	"kbd"
    Option "AutoRepeat" "500 30"
    Option "XkbRules"	"xorg"
    Option "XkbModel"	"pc101"
    Option "XkbLayout"	"pl"
    Option "XkbVariant"	"pl"
EndSection

Section "InputDevice"
    Identifier	"Mouse1"
    Driver	"mouse"
    Option "Protocol"    "Auto"
    Option "Device"      "/dev/mouse"
    Option "Emulate3Buttons"
EndSection

Section "Monitor"
    Identifier  "monitor0"
    HorizSync   31.5 - 57.0  #(ta wartosc 31.5 - 57.0 zmieniam na 31.5 - 70 wydaje mi sie ze jak tak zrobie to zwiekszy mi sie zakres 85hz az do rozdzielczosci 1024x768 sprawdze i powiem) 
    VertRefresh 50-90 # (ta wartosc pozostawiam bez zmian bo 90 to max co moj monitor moze)
EndSection
# (zastanawia mnie dlaczego sa podane sekcje device 2 razy ??????? jedna dla standart vga a druga dla nv wiec usune potem sekcje standart vga a potem zmienie  draiver w sekcji device "nv" na nvidia i zobacze co sie stanie  )
Section "Device"
    Identifier	"Standard VGA"
    VendorName	"Unknown"
    BoardName	"Unknown"
    Driver     "vga"
EndSection

Section "Device"
    Identifier  "card0"
    Driver      "nv"
    EndSection

Section "Screen"
    Identifier  "Screen 1"
    Device      "card0"
    Monitor     "monitor0"
    DefaultDepth 24
    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

Section "ServerLayout"
    Identifier  "Simple Layout"
    Screen "Screen 1"
    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"
EndSection
dobra ide testowac [/code]

jogofrugo
Użytkownik
Posty: 9
Rejestracja: 2007-04-20, 15:10

Re: problemy z ekranem

Post autor: jogofrugo »

wszystko sie chyba wyjasnilo otuz te device standart vga mozna bylo wyzucic ale sterowniki nv na nvidia nie dzialaja i wywala mi automatyczna rozdzielczosc i powiem cos jeszcze pierwszy raz w zyciu ujzalem na moim ekranie rozdzialke 1280x1024 heheheh fakt ze w 60hz heheheh ale ujzalem wiecej nie bede robil bo mi monitor sie zagotuje wiec zostane przy 1024x768 oto moj nowy kod oczywiscie musialem do tamtego wstawic jeszcze jedna linijke kodu bo wywalalo mi blad klawiatury chyba linijka 32 ponizej kod nowy i nowe pytanie co zrobic z sterownikami nvidi czy instalowac np jakies stare sterowniki i sprawdzic czy dzialaja a xorg.conf po instalacji wstawic taki sam jak mam teraz ze zmieniana nazwa sterownika z nv na nvidia

Kod: Zaznacz cały

Section "ServerLayout"
    Identifier  "Simple Layout"
    Screen "Screen 1"
    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "Module"
    Load        "dbe"  	# Double buffer extension

    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection
    Load        "type1"
    Load        "freetype"
    Load       "glx"
EndSection
Section "Files"
    RgbPath	"/usr/X11R6/lib/X11/rgb"
    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/TTF/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/cyrillic/"
EndSection
Section "ServerFlags"
EndSection

Section "InputDevice"
    Identifier     "Keyboard0"
    Driver         "kbd"
    Option "AutoRepeat" "500 30"
    Option "XkbRules"	"xorg"
    Option "XkbModel"	"pc101"
    Option "XkbLayout"	"pl"
    Option "XkbVariant"	"pl"
EndSection

Section "InputDevice"
    Identifier	"Mouse1"
    Driver	"mouse"
    Option "Protocol"    "Auto"
    Option "Device"      "/dev/mouse"
    Option "Emulate3Buttons"
EndSection

Section "Monitor"
    Identifier  "monitor0"
    HorizSync   31.5 - 70.0 
    VertRefresh 50-90
EndSection

Section "Device"
    Identifier  "card0"
    Driver      "nv"
    EndSection

Section "Screen"
    Identifier  "Screen 1"
    Device      "card0"
    Monitor     "monitor0"
    DefaultDepth 24
    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection
Ostatnio zmieniony 2007-04-21, 12:49 przez jogofrugo, łącznie zmieniany 1 raz.

kolert83
Użytkownik
Posty: 69
Rejestracja: 2006-10-16, 18:29
Lokalizacja: Śląsk

Re: problemy z ekranem

Post autor: kolert83 »

Aby miec 85 hz w moim Flatronie(17'') mam ustawione H 30-70 V 50-160 i działa. Kiedyś dla bezpieczeństwa miałem H 30-69 V 40-120 ale to był ustawienia z innego monitora - WIĘC jak znajdziesz na jakich ustawieniach masz 85 hz ustaw je w xorgconfigu.

jogofrugo
Użytkownik
Posty: 9
Rejestracja: 2007-04-20, 15:10

Re: problemy z ekranem

Post autor: jogofrugo »

:rotfl: :mrgreen: Zgadzam sie z kolega troszke podpedzilem zakres hz i khz i wszystko gra a pozatym z tego co zauwazylem nie wszystkie stery nvidi chodzily mi dobrze jestem teraz u dziewczyny takze nie powiem jakie dokladnie ale napewno dzialal mi ster 5336 i cos z 87?? bo 9??? nie dzialal mi wcale tzn dzialal ale rozdzielczosc 800x600@50hz takze zostalem przy tych sterach z 87??

Teraz chcial bym cos powiedziec dla pozostalych uzytkownikow ktorzy sa dopiero na samym poczatku takie moje spostrzerzenie malo znaczace.

1. po instalacji próbowac najpierw skonfigurowac xorg.conf tak aby na vesa dzialaly rozdzielczosci i odswieżanie ktore chemy uzyskac
2. nastepnie jesli wszysko juz gra poszukac sobie sterow do nvidi najlepiej zaczac sciagac od NVIDIA-Linux-x86-1.0-5???-pkg.run konczac na NVIDIA-Linux-x86-1.0-97??-pkg.run sciagnac sobie ich z 5 sztuk i sprawdzic ktory dziala bo nie wszystkie dzialaja.
3. nie(spacja)poddawac sie ja walczylem 3 dni zanim napisalem cos na forum.

tak wygladala moja sekcja monitora w pliku xorg.conf

Kod: Zaznacz cały

Section "Monitor" 
    Identifier     "Monitor0" 
    VendorName     "Monitor Vendor" 
    ModelName      "Monitor Model" 
    VertRefresh     75 
EndSection 
a tak wyglada xorg.conf po modyfikacji i zaznajomieniu sie z tematem v i h

Kod: Zaznacz cały

Section "Monitor" 
    Identifier  "monitor0" 
    HorizSync   31.5 - 70.0 
    VertRefresh 50-90 
EndSection
zdaje sie mala roznica ale efekt jest super

Dziekuje panowie za pomoc serdecznie i bardzo, proponuje zamknac temat wszystko juz zostalo wyjasnione jeszcze raz bardzo dziekuje. Mam taka nadzieje ze moj temat pomógl tez innym uzytkownikom mnie osobiscie pomogl bardzo uwierzcie mi bo 3 dni przesiedzialem na odswieżaniu 50hz i 60hz wiezcie mi "wzrok spawacza oczy biedronki"

Jestescie WIELCY :ok:

[ Komentarz dodany przez: Radek_R: 2007-04-22, 16:05 ]
A na końcu tych perypetii warto zapoznać się z tym odnośnikiem.
Ostatnio zmieniony 2007-04-22, 15:04 przez jogofrugo, łącznie zmieniany 1 raz.

ODPOWIEDZ