Witam i dziekuje wszystkim za odpowiedzi
chwilowo podpialem neo pod kompa dziewczyny na windzie a sam siedze 'za nia' na sieciowce.
narazie podam pobiezne info, a jeszcze raz bede mial czas walczyc we wtorek wiec wtedy podam rozszerzone info
____0 pisze:To ze nie mozesz skompilowac najnowsze eagle-usb to nie znaczy ze masz modem w wersji E4(ja tak mialem).
hmm czy opis 9042 nie swiadczy o 4 wersji modemu?
Afro pisze:Po pierwsze make install nie tworzy tych plików (one już sa).
install nie, ale najpierw dalem samo make wiec sadzilem ze je utworzylo. przyznam ze na daty wtedy nie patrzylem
songoman pisze:odstwowa sprawa jest taka że udostępnione na stronie żródła dla ueagle4-atm są stare, należy wejść do CVS-u tam i z tamtąd poprać drivera, od jąder 2.6.19 bodajże należy używać nowego - jak chcesz wyśle Ci na maila "gotowca".
wiec pewnie dlatego mialem problem. sporo sie naszukalem pod haslo "ID 1110:9042 Analog Devices Canada" ale przyznam ze w zadnych poradach na forach nikt nie wspomnial ze na stronie sa nieaktualne
jesli chcesz podeslac to chetnie skozystam
sleaquit[at]poczta.onet.pl
robilem sporo roznych prob takze z ueagle4-data-1.0.tar.gz zamiast ueagle-data-1.1.tar.tar w miedzy czasie moich i Waszych postow ale jeszcze popracuje we wtorek i zaprezentuje wyniki sukcesu ewentualnie porazki
[ Dodano: 2007-10-04, 08:44 ]
zdobylem nowy firmware, tym razem po podlaczeniu modem jest wykrywalny
lsusb
Kod: Zaznacz cały
Bus 2 Device 3: ID 1110:9041 Analog Devices Canada, Ltd (Allied Telesyn)
dmesg
Kod: Zaznacz cały
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
NET: Registered protocol family 8
NET: Registered protocol family 20
[ueagle-atm] driver ueagle 1.4 loaded
usb 2-1: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9042) : Eagle IV
usb 2-1: reset full speed USB device using uhci_hcd and address 2
usb 2-1: [ueagle-atm] pre-firmware device, uploading firmware
usb 2-1: [ueagle-atm] loading firmware ueagle-atm/eagleIV.fw
usbcore: registered new interface driver ueagle-atm4
usb 2-1: [ueagle-atm] firmware uploaded
usb 2-1: USB disconnect, address 2
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9041) : Eagle IV
usb 2-1: reset full speed USB device using uhci_hcd and address 3
usb 2-1: [ueagle-atm] (re)booting started
usb 2-1: [ueagle-atm] sending DSP page 0
usb 2-1: [ueagle-atm] sending DSP page 3
usb 2-1: [ueagle-atm] sending DSP page 4
usb 2-1: [ueagle-atm] ATU-R firmware version : a10050b
usb 2-1: [ueagle-atm] stat : 1
usb 2-1: [ueagle-atm] stat : 1
usb 2-1: [ueagle-atm] stat : 1
usb 2-1: [ueagle-atm] stat : 5
usb 2-1: [ueagle-atm] stat : 5
usb 2-1: [ueagle-atm] stat : 5
usb 2-1: [ueagle-atm] sending DSP page 29
usb 2-1: [ueagle-atm] sending DSP page 5
usb 2-1: [ueagle-atm] sending DSP page 34
usb 2-1: [ueagle-atm] sending DSP page 31
usb 2-1: [ueagle-atm] sending DSP page 8
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] sending DSP page 33
usb 2-1: [ueagle-atm] sending DSP page 10
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] sending DSP page 11
usb 2-1: [ueagle-atm] sending DSP page 12
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] sending DSP page 15
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] sending DSP page 16
usb 2-1: [ueagle-atm] sending DSP page 23
usb 2-1: [ueagle-atm] sending DSP page 20
usb 2-1: [ueagle-atm] sending DSP page 26
usb 2-1: [ueagle-atm] stat : 6
usb 2-1: [ueagle-atm] sending DSP page 27
usb 2-1: [ueagle-atm] sending DSP page 25
usb 2-1: [ueagle-atm] modem operational
usb 2-1: [ueagle-atm] setting new timeout 1
usb 2-1: [ueagle-atm] setting new timeout 1
nastepnie
dmesg
lsmod|grep ueagle
Kod: Zaznacz cały
ueagle4_atm 29368 0
usbatm 19456 1 ueagle4_atm
lsmod|grep ppp
Kod: Zaznacz cały
pppoatm 8064 0
ppp_generic 26772 1 pppoatm
slhc 9856 1 ppp_generic
atm 44212 2 pppoatm,usbatm
/etc/ppp/peers/neostrada
Kod: Zaznacz cały
user "ustawiony_login@neostrada.pl"
plugin pppoatm.so 0.35
usepeerdns
defaultroute
persist
noauth
/etc/ppp/chap-secrets
/etc/ppp/pap-secrets
Kod: Zaznacz cały
"ustawiony_login@neostrada.pl" * "ustawione_haslo"
pppd call neostrada
Kod: Zaznacz cały
Plugin pppoatm.so loaded.
PPPoATM plugin_init
PPPoATM setdevname_pppoatm - SUCCESS:0.35
dmesg
Kod: Zaznacz cały
PPP BSD Compression module registered
PPP Deflate Compression module registered
interfejs ppp0 wstaje ale pingi nigdzie nie wychodza, chociaz dnsy mam ustawione
po jakims czasie dmesg pokazuje
tcpdump przez kilka minut nie rejestruje zadnego ruchu, dopiero po tym czasie rejestruje troche przychodzacych pakietow ale dalej nic nie mozna gdzies wyslac, nawet pingnac dowolnego adresu skad przychadza pakiety, po prostu cisza
problem moze tkwic w konfiguracji ppp?
z gory dziekuje za pomoc