PM-Timer Bug acpi_pm_good jak to wyłączyć?

Instalacja Slackware Linux, problemy i wstępna konfiguracja, aktualizacje do nowszych wersji.

Moderatorzy: Moderatorzy, Administratorzy

overburn
Użytkownik
Posty: 38
Rejestracja: 2005-09-14, 12:04

PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: overburn »

Witam

Instaluje sobie S 12.2 na takim tam zabytkowym ibmie i mi cos takiego wylatuje:

Kod: Zaznacz cały

ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
Tak się zastanawiam czy do wyłączenia tego dziadostwa trzeba jądro rekompiloać czy jakiś moduł wystarczy załadować?

Albo może jak sprawdzić czy dany chipset akurat ma tego buga? bo może ma? pewny nie jestem.
largo3
Moderator
Posty: 1297
Rejestracja: 2006-06-11, 11:08

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: largo3 »

Jeśli już zainstalowałeś system dopisz do parametrów kernala w bootmenadżerze acpi_pm_good. Jeśli dzieje się to w czasie instalacji to podaj ten parametr w momencie wyboru kernela.
Albo może jak sprawdzić czy dany chipset akurat ma tego buga? bo może ma? pewny nie jestem.
Dowiedz się jaki to dokładnie chipset i sprawdź w Google. ;)
Zobacz jeszcze ten skrypt.
Ostatnio zmieniony 2009-07-13, 08:58 przez largo3, łącznie zmieniany 2 razy.
UNIX is basically a simple operating system, but you have to be a genius to understand the simplicity.
-- Dennis Ritchie
Linux Registered User #419452
overburn
Użytkownik
Posty: 38
Rejestracja: 2005-09-14, 12:04

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: overburn »

Co do bootmanadżera to masz na myśli lilo czy guba? bo do lilo to jakoś nie mogę tego wsadzić, a grubego nie używam:]


Co do skryptu sprawdzającego to niestety mam jakieś aua:

Kod: Zaznacz cały

root@epsilon:~# ./pmtmr_test 0x4e8
./pmtmr_test: Invalid port address: 0x4e8

root@epsilon:~#
Co do sprawdzenia chipsetu ale konkretnie ktorego chipsetu to się tyczy bo na płycie mam ich zatrzęsienie min broadcoma intela ibma

Kod: Zaznacz cały

root@epsilon:~# lspci -v -v
00:00.0 Host bridge: Broadcom CNB20LE Host Bridge (rev 06)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 96, Cache Line Size: 32 bytes
        Kernel modules: sworks-agp

00:00.1 Host bridge: Broadcom CNB20LE Host Bridge (rev 06)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 96, Cache Line Size: 32 bytes
        Kernel modules: sworks-agp

00:02.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
        Subsystem: IBM Netfinity 10/100
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 100 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 27
        Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at 2200 [size=64]
        Region 2: Memory at fea00000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: e100
        Kernel modules: eepro100, e100

00:0a.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
        Subsystem: IBM Netfinity 10/100
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 100 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 25
        Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at 2240 [size=64]
        Region 2: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: e100
        Kernel modules: eepro100, e100

00:0f.0 ISA bridge: Broadcom OSB4 South Bridge (rev 51)
        Subsystem: Broadcom OSB4 South Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Kernel modules: i2c-piix4

00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8a [Master SecP PriP])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64
        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
        Region 4: I/O ports at 0700 [size=16]
        Kernel driver in use: Serverworks_IDE
        Kernel modules: pata_serverworks

00:0f.2 USB Controller: Broadcom OSB4/CSB5 OHCI USB Controller (rev 04) (prog-if 10 [OHCI])
        Subsystem: Broadcom OSB4/CSB5 OHCI USB Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
        Latency: 96 (20000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

01:05.0 RAID bus controller: IBM ServeRAID Controller
        Subsystem: IBM ServeRAID-4L
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 96, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at f7ffe000 (32-bit, prefetchable) [size=8K]
        [virtual] Expansion ROM at 50010000 [disabled] [size=32K]
        Kernel driver in use: ips
        Kernel modules: ips

01:06.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (rev 54) (prog-if 00 [VGA controller])
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
        [virtual] Expansion ROM at 50000000 [disabled] [size=64K]
        Kernel driver in use: s3fb
        Kernel modules: s3fb

joi
Użytkownik
Posty: 151
Rejestracja: 2004-10-12, 20:32
Lokalizacja: raczej nie stąd ;)
Kontakt:

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: joi »

a jak wygląda /proc/ioports i cały dmesg?
overburn
Użytkownik
Posty: 38
Rejestracja: 2005-09-14, 12:04

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: overburn »

ioports

Kod: Zaznacz cały

root@epsilon:~# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:0f.1
  0170-0177 : serverworks
01f0-01f7 : 0000:00:0f.1
  01f0-01f7 : serverworks
0320-0323 : wd7000
0350-0353 : wd7000
0376-0376 : 0000:00:0f.1
  0376-0376 : serverworks
03c0-03df : vga+
03f2-03f5 : floppy
03f6-03f6 : 0000:00:0f.1
  03f6-03f6 : serverworks
03f7-03f7 : floppy DIR
03f8-03ff : serial
0430-0437 : pnp 00:01
0438-0439 : pnp 00:01
04e0-04e3 : ACPI PM1a_EVT_BLK
04e4-04e5 : ACPI PM1a_CNT_BLK
04e8-04eb : ACPI PM_TMR
04f0-04f7 : ACPI GPE0_BLK
0600-0600 : pnp 00:0c
0700-070f : 0000:00:0f.1
  0700-070f : serverworks
0cf8-0cff : PCI conf1
0f50-0f58 : pnp 00:0c
2200-223f : 0000:00:02.0
  2200-223f : e100
2240-227f : 0000:00:0a.0
  2240-227f : e100
A Tu Dmesg

Kod: Zaznacz cały

Linux version 2.6.27.7-smp (root@midas) (gcc version 4.2.4) #2 SMP Thu Nov 20 22:32:43 CST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
 BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffec340 (usable)
 BIOS-e820: 000000003ffec340 - 000000003fff0000 (ACPI data)
 BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0x3ffec max_arch_pfn = 0x100000
kernel direct mapping tables up to 38000000 @ 7000-c000
ACPI: RSDP 000FDFD0, 0014 (r0 IBM   )
ACPI: RSDT 3FFEFF80, 002C (r1 IBM    SEREMRLD     1000 IBM  45444F43)
ACPI: FACP 3FFEFF00, 0074 (r1 IBM    SEREMRLD     1000 IBM  45444F43)
ACPI: DSDT 3FFEC340, 3AAC (r1 IBM    SEREMRLD     1000 MSFT  100000B)
ACPI: FACS 3FFEFE40, 0040
ACPI: APIC 3FFEFE80, 005E (r1 IBM    SEREMRLD     1000 IBM  45444F43)
127MB HIGHMEM available.
896MB LOWMEM available.
  mapped low ram: 0 - 38000000
  low ram: 00000000 - 38000000
  bootmap 00008000 - 0000f000
(8 early reservations) ==> bootmem [0000000000 - 0038000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 0000a6a790]    TEXT DATA BSS ==> [0000100000 - 0000a6a790]
  #4 [0000a6b000 - 0000a6f000]    INIT_PG_TABLE ==> [0000a6b000 - 0000a6f000]
  #5 [000009d000 - 0000100000]    BIOS reserved ==> [000009d000 - 0000100000]
  #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
  #7 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
found SMP MP-table at [c009e1d0] 0009e1d0
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00038000
  HighMem  0x00038000 -> 0x0003ffec
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009d
    0: 0x00000100 -> 0x0003ffec
On node 0 totalpages: 262025
free_area_init_node: node 0, pgdat c093eb00, node_mem_map c1000000
  DMA zone: 3965 pages, LIFO batch:0
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 32492 pages, LIFO batch:7
ACPI: PM-Timer IO Port: 0x4e8
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 14, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x0d] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 13, version 17, address 0xfec01000, GSI 16-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 3 global_irq 30 dfl dfl)
Enabling APIC mode:  Flat.  Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec01000)
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
PERCPU: Allocating 39452 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259977
Kernel command line: auto BOOT_IMAGE=Linux ro root=802 vt.default_utf8=1
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PMTIMER calibration value
Detected 1128.532 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1028912k/1048496k available (6388k kernel code, 18832k reserved, 2148k data, 424k init, 130992k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe19000 - 0xfffff000   (1944 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0963000 - 0xc09cd000   ( 424 kB)
      .data : 0xc073d137 - 0xc0956278   (2148 kB)
      .text : 0xc0100000 - 0xc073d137   (6388 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 2257.06 BogoMIPS (lpj=4514128)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Pentium(R) III CPU family      1133MHz stepping 01
Booting processor 1/0 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 2257.27 BogoMIPS (lpj=4514557)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Pentium(R) III CPU family      1133MHz stepping 01
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (4514.34 BogoMIPS).
net_namespace: 776 bytes
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  2647.000 MB/sec
xor: using function: pIII_sse (2647.000 MB/sec)
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
PCI: 0000:00:02.0 reg 10 32bit mmio: [febff000, febfffff]
PCI: 0000:00:02.0 reg 14 io port: [2200, 223f]
PCI: 0000:00:02.0 reg 18 32bit mmio: [fea00000, feafffff]
pci 0000:00:02.0: supports D1
pci 0000:00:02.0: supports D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
PCI: 0000:00:0a.0 reg 10 32bit mmio: [febfe000, febfefff]
PCI: 0000:00:0a.0 reg 14 io port: [2240, 227f]
PCI: 0000:00:0a.0 reg 18 32bit mmio: [fe900000, fe9fffff]
pci 0000:00:0a.0: supports D1
pci 0000:00:0a.0: supports D2
pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.0: PME# disabled
PCI: 0000:00:0f.1 reg 20 io port: [700, 70f]
PCI: 0000:00:0f.2 reg 10 32bit mmio: [febfd000, febfdfff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Root Bridge [PCI1] (0000:01)
PCI: 0000:01:05.0 reg 10 32bit mmio: [f7ffe000, f7ffffff]
PCI: 0000:01:05.0 reg 30 32bit mmio: [0, 7fff]
PCI: 0000:01:06.0 reg 10 32bit mmio: [f8000000, fbffffff]
PCI: 0000:01:06.0 reg 30 32bit mmio: [0, ffff]
bus 01 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Interrupt Link [LPE1] (IRQs *10)
ACPI: PCI Interrupt Link [LPE2] (IRQs *10)
ACPI: PCI Interrupt Link [LPVI] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [LPUS] (IRQs *11)
ACPI: PCI Interrupt Link [LPSA] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [LP1A] (IRQs *7)
ACPI: PCI Interrupt Link [LP1B] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [LP2A] (IRQs *9)
ACPI: PCI Interrupt Link [LP2B] (IRQs) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:06: IRQ 5 override to edge, high
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
tracer: 772 pages allocated for 65536 entries of 48 bytes
   actual entries 65620
system 00:01: ioport range 0x438-0x439 has been reserved
system 00:01: ioport range 0x430-0x437 has been reserved
system 00:0c: ioport range 0x600-0x600 has been reserved
system 00:0c: ioport range 0xf50-0xf58 has been reserved
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 io port: [0, ffff]
bus: 01 index 1 mmio: [0, ffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
JFS: nTxBlock = 8041, nTxLock = 64329
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Nov 20 2008 22:30:39) installed
msgmni has been set to 1754
async_tx: api initialized (async)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Firmware left e100 interrupts enabled; disabling
pci 0000:00:0a.0: Firmware left e100 interrupts enabled; disabling
pci 0000:01:06.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
serverworks 0000:00:0f.1: IDE controller (0x1166:0x0211 rev 0x00)
serverworks 0000:00:0f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x0700-0x0707
    ide1: BM-DMA at 0x0708-0x070f
Probing IDE interface ide0...
hda: OIP-SD2400A/BM, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 1.00
Loading iSCSI transport class v2.0-870.
rdac: device handler registered
hp_sw: device handler registered
emc: device handler registered
alua: device handler registered
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2456]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
ips 0000:01:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
scsi2 : IBM PCI ServeRAID 7.12.05  Build 761 <ServeRAID 4L>
scsi 2:0:0:0: Direct-Access     IBM      SERVERAID        1.00 PQ: 0 ANSI: 2
scsi 2:0:15:0: Processor         IBM      SERVERAID        1.00 PQ: 0 ANSI: 2
scsi 2:1:8:0: Processor         IBM      FTlV1 S2         0    PQ: 0 ANSI: 2
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.02.01-k7
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.7
Copyright(c) 2004-2008 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
        with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
stex: Promise SuperTrak EX Driver version: 3.6.0000.1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 71131136 512-byte hardware sectors (36419 MB)
sd 2:0:0:0: [sda] Assuming Write Enabled
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] 71131136 512-byte hardware sectors (36419 MB)
sd 2:0:0:0: [sda] Assuming Write Enabled
sd 2:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
Driver 'sr' needs updating - please use bus_type methods
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LPUS] enabled at IRQ 11
ohci_hcd 0000:00:0f.2: PCI INT A -> Link[LPUS] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:0f.2: OHCI Host Controller
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0f.2: irq 11, io mem 0xfebfd000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-smp ohci_hcd
usb usb1: SerialNumber: 0000:00:0f.2
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: New USB device found, idVendor=04d9, idProduct=1603
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB Keyboard
usb 1-1: Manufacturer:
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    342 MB/s
raid6: int32x2    372 MB/s
raid6: int32x4    315 MB/s
raid6: int32x8    287 MB/s
raid6: mmxx1     1013 MB/s
raid6: mmxx2     1247 MB/s
raid6: sse1x1     833 MB/s
raid6: sse1x2    1235 MB/s
raid6: using algorithm sse1x2 (1235 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
input:   USB Keyboard as /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.0/input/input1
input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:0f.2-1
input:   USB Keyboard as /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.1/input/input2
input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:0f.2-1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 424k freed
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button (FF) [PWRF]
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
Linux agpgart interface v0.103
sd 2:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:15:0: Attached scsi generic sg1 type 3
scsi 2:1:8:0: Attached scsi generic sg2 type 3
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:02.0: PCI INT A -> GSI 27 (level, low) -> IRQ 27
e100 0000:00:02.0: PME# disabled
e100: eth0: e100_probe: addr 0xfebff000, irq 27, MAC addr 00:02:55:c6:1e:6e
e100 0000:00:0a.0: PCI INT A -> GSI 25 (level, low) -> IRQ 25
e100 0000:00:0a.0: PME# disabled
e100: eth1: e100_probe: addr 0xfebfe000, irq 25, MAC addr 00:02:55:c6:1e:6f
agpgart-serverworks 0000:00:00.0: can't determine aperture size
agpgart-serverworks 0000:00:00.0: agp_backend_initialize() failed
agpgart-serverworks: probe of 0000:00:00.0 failed with error -22
agpgart-serverworks 0000:00:00.1: can't determine aperture size
agpgart-serverworks 0000:00:00.1: agp_backend_initialize() failed
agpgart-serverworks: probe of 0000:00:00.1 failed with error -22
piix4_smbus 0000:00:0f.0: Host SMBus controller not enabled!
s3fb 0000:01:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
fbcon: S3 Trio64V+ (fb0) is primary device
Console: switching to colour frame buffer device 80x30
fb0: S3 Trio64V+ on 0000:01:06.0, 1 MB RAM, 61 MHz MCLK
hda: DMA timeout retry
hda: timeout waiting for DMA
Adding 3908480k swap on /dev/sda1.  Priority:-1 extents:1 across:3908480k
fuse init (API version 7.9)
EXT3 FS on sda2, internal journal
ppdev: user-space parallel port driver
lp: driver loaded but no devices found
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: eth1: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth1: no IPv6 routers present
joi
Użytkownik
Posty: 151
Rejestracja: 2004-10-12, 20:32
Lokalizacja: raczej nie stąd ;)
Kontakt:

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: joi »

wygląda na to, że te 2 linijki:

Kod: Zaznacz cały

if ((pmtmr_ioport & 0xff) != 0x08)
		error(1, 0, "Invalid port address: 0x%x\n", pmtmr_ioport);
nie mają sensu, usuń je i spróbuj jeszcze raz

jak wyjdzie że jednak chipset ma tego buga, możesz spróbować dodać jako parametr kernela:

Kod: Zaznacz cały

clocksource=tsc
i sprawdź czy czas wg systemu płynie zgodnie z rzeczywistością :)
Ostatnio zmieniony 2009-07-14, 16:16 przez joi, łącznie zmieniany 2 razy.
overburn
Użytkownik
Posty: 38
Rejestracja: 2005-09-14, 12:04

Re: PM-Timer Bug acpi_pm_good jak to wyłączyć?

Post autor: overburn »

Dzieki wywalenie tej linijki pomogło. Niestety jest bug więc workaround musi zostać bo nawet z tego co się orientuje specjalnie jakoś spadku wydajności to nie powoduje, bo ponoć aby powoduje on częstsze odpytywanie acpi w celu dokładnego sprawdzenia. Co do czasu od 24 h nic się nie zmieniło jest poprawnie.
ODPOWIEDZ